Nissan Xterra Recalls

Certain light duty trucks and sport utility vehicles equipped with automatic transmissions fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect." These vehicles could have a shift cable lock plate that is too brittle and can break. The gear shift lever and the "PRNDL" indicator may move, but the transmission will not shift out of the "Park" position. Also, the gear indicated on the display may differ from the gear engaged in the transmission. If the driver selects "Drive" and the transmission is actually in "Reverse", a vehicle crash could occur.

On certain pickup trucks and sport utility vehicles equipped with a supercharger, under certain conditions, such as full throttle in low gear when the engine is not fully warmed up and at cold ambient temperature, the amount of intake airflow through the air flow meter may exceed the maximum preset diagnosis limit value. This will cause the engine control system to go into the failsafe mode. Under this condition, the malfunction indicator lamp will illuminate and engine speed will not exceed 2400 rpm regardless of the throttle position, increasing the risk of a crash.

On certain 4-wheel drive pickup trucks and sport utility vehicles, water may enter the rear axle housing due to inadequate sealing of the anti-lock braking system (ABS) sensor. This can result in corrosion and eventual failure of the wheel bearing. If this occurs, the wheel assembly could separate from the vehicle, increasing the risk of a crash.

On certain passenger and sport utility vehicles, the clock spring electrical connector may not be fully secured to the driver air bag module squib pin connector. If the connector comes loose, the driver air bag will not deploy in a crash, increasing the risk of injury.

Nissan North America, Inc. (Nissan) is recalling certain 2008-2011 Titan, Frontier, Xterra, Pathfinder, Armada, and 2008-2009 Quest vehicles. The resin emblem on the driver's air bag cover may develop cracks and detach during air bag deployment.

Nissan is recalling certain model year 2012 Frontier, Pathfinder, and Xterra two-wheel drive vehicles manufactured from June 19, 2012, through July 12, 2012. These vehicles may have been equipped with front wheel hubs that may not meet the design hardness specifications. A wheel hub that was manufactured below hardness specification may wear prematurely and eventually crack.

NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 INFINITI FX, MODEL YEAR 2012 INFINITI M, MODEL YEAR 2011-2012 NISSAN FRONTIER, MODEL YEAR 2011-2012 NISSAN XTERRA, MODEL YEAR 2011-2012 NISSAN PATHFINDER, AND MODEL YEAR 2012 NISSAN NV VEHICLES. SOME OF THE BOLTS THAT CONNECT THE ENGINE OIL COOLER AND THE ENGINE OIL FILTER TO THE ENGINE IN THESE VEHICLES MAY HAVE BEEN MANUFACTURED TO BELOW SPECIFICATION STRENGTH. AS A RESULT, THE BOLT MAY BREAK AT THE OIL FILTER ATTACHMENT POINT AND CAN CAUSE AN ENGINE OIL LEAK.

NISSAN IS RECALLING CERTAIN VEHICLES THAT WERE EQUIPPED WITH A GARMIN NUVI MODEL 750 NAVIGATION SYSTEM. THE BATTERIES CONTAINED IN THE AFFECTED GPS UNITS CAN OVERHEAT.

MARATHON IS RECALLING CERTAIN SEAT COVERS, BRAND SUPERHIDES WITH PART NUMBERS 593, 594, 578, 960, 228, 228-09, 267-08, 333, 625, AND 630, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE SEAT COVERS ARE MADE OF HEAVIER THREAD AND ARE NOT COMPATIBLE WITH SEATS CONTAINING SIDE AIRBAGS. THE HEAVIER SEAT COVER COULD INTERFERE WITH FULL DEPLOYMENT OF THE AIRBAG IN THE EVENT OF A CRASH.

NISSAN IS RECALLING CERTAIN FRONT AND REAR LOWER LINKS, P/NOS. 54501ZQ00A, 54500ZQ00A, 551A1ZQ00A, 551A0ZQ00A , 54501EA00A, 54500EA00A, 551A1EA500, 551A0EA500, 54501ZR00A, AND 54500ZR00A, SOLD BETWEEN NOVEMBER 25, 2009 AND MAY 14, 2010 AS REPLACEMENT PARTS FOR MODEL YEAR 2004 THROUGH 2010 TITAN, ARMADA, AND QX56, AND MODEL YEARS 2005 THROUGH 2010 FRONTIER, XTERRA, AND PATHFINDER VEHICLES. THE LOWER CONTROL LINK ASSEMBLY HAS TWO CYLINDRICAL COLLARS FORMING THE INBOARD ATTACHMENT POINTS TO THE CHASSIS. DUE TO AN IMPROPER WELDING PROCESS SOME COLLARS MAY CONTAIN WELDS THAT DO NOT MEET STRENGTH SPECIFICATIONS.